Best Tips to Fix Errors of Docking Station Drivers
What are common docking station driver’s errors?
If you often use Docking station drivers, you must have encountered errors that are difficult to format. It is the USB that interferes in the working process. When encountering this error, the system will open an error message window with the words “Windows was unable to complete the format”.
It is to warn users that the Windows operating system cannot handle the format process on the desired device.
Don’t worry, if you encounter this error, try these ways. We have discussed in the Blog supports. We have also mentioned the instructions below. These are to fix the error as well as the remedies through the content in the article below.
The reason why the computer cannot format the Docking station drivers?
Docking station drivers are a portable device. And it can connect to all kinds of computers easily for backup or data transfer. Users frequently use them to connect on many different computer devices. Moreover, USB drives are difficult to avoid the risk of being damaged or infected with viruses.
This is the first and most common cause that usually occurs when USB plugs at:
- public Internet spots
- photo shops that carries viruses
Preventing the Format operation from causing your USB to infect viruses
When a user plugs a USB into the USB port of a device that does not have anti-virus software installed, the USB will be invaded by some types of viruses, preventing the Format operation from causing your USB to infect viruses.
We can withdraw work by filling the Docking station drivers drive with dangerous data. And this makes the USB drive stop working and is not easy to format.
The Docking station drivers has a virus
The solution in this case is that you try to use anti-virus software to remove viruses on your USB. After removing the virus, you proceed to format the USB normally.
USB locked in write-protect mode is difficult to format Docking station drivers
Some special USBs are equipped with a lock button design with a lock feature that prevents data from being copied to the USB, that is, the USB can only read data but cannot write it. This is also a common cause of not being able to format the USB. Check to see if your USB is in this mode then see where the button is on the USB and turn it off. Then do Format again.
Docking station drivers has an unknown capacity error
When you suddenly unplug the USB from the computer without first performing a safe disconnect, it will cause the flash memory. Unknown Capacity will occur. At this time, you will get an error message “Windows unable to complete format” when you proceed to reformat.
This error also leads to not being able to open that Docking station drivers because the capacity is unknown (Unknown Capacity).
Hardware damaged Docking station drivers
After a long time of use, the damage is inevitable. USB too. It is inherently a small, portable device that is easy to carry. Hence, sometimes it often bumps. Moreover, it causes hardware damage. In addition, a possible cause for the docking station to fail during your use.
And not be able to format is that the frequent unplugging and plugging operation also causes the USB to get damage. This error is very easy to spot. After identifying this error, please bring the USB to the service center for inspection and repair.
Faulty firmware cannot format USB
When using cheap USB lines, this is a very common error. USB operates by Firmware software. And of course, when the firmware fails, all USB operations will also fail accordingly and the operations cannot take place normally, including reformatting the Docking station drivers.
Error “Windows was unable to complete the format” cannot format the USB
Instructions on how to fix the error of not being able to format Docking station drivers
Method 1: Format the USB drive to another partition format
One of the simplest ways to fix the error of USB not being formatted is to format the USB drive to another partition format. To do everyone follow these steps
Step 1 : To be able to format the USB drive to another partition format, first plug the USB drive that needs to be processed into the computer → right-click the USB drive after the USB is successfully connected → select Format . Now the Format USB window is opened, please change the FAT 32 format to NTFS or exFAT format in the File System section.
Change FAT 32 format to NTFS or another format
Step 2: Next in the Quick Format option, please remove (✓) → click and select Start to start the Docking station drivers format process.
Uncheck the Quick Format option, then select Start
Check if the error has been fixed or not after the USB is formatted.
Method 2: Format Docking station drivers with Disk Management tool
To fix errors on the USB drive, sometimes in some specific cases to format the USB drive, you can use the Disk Management tool. This is a tool that is pre-installed by default on laptops and computers using Windows operating system, so everyone can take advantage and follow the following instructions:
Step 1: First, plug and connect the USB drive to the computer → then right-click the Computer (This PC) icon on the desktop → select Manage in the window that opens.
The biggest problem of Type-C is still the price?
Type-C is the inclusion of all the current protocols and the Docking station drivers IF problem may convince the owners of these protocols to provide a freeway like how they developed the USB port in the past to communicate. close to users?
Design problem docking station drivers:
Concerns are there about the physical design of USB-C, as the connector seems a bit flimsy with a hollow plug in it that seems flimsy. In contrast, Apple’s Lightning uses a sturdy thick metal plug, which is much more resilient.
Conclusion docking station drivers
More worrisomely, there has been a lot of concern about the uncontrolled state of the Docking station drivers. This has resulted in some dangerous accessories using unsupported voltage levels, which have damaged the USB-C standard host device.
